Decide Between Replacing a Pump and Building a New Pit
If the basement already has a pit, replacing the pump is a simple job that takes an hour or two. If there is no pit, a new basin must be set into the slab, which takes breaking and removing concrete.
Before you start, find out where the water enters the basement. The pit belongs at the low point where water naturally collects.
The Steps in Order
This is the sequence for a new pit.
Mark and cut
Mark the pit outline and cut the slab with a saw or a breaker. Wear a respirator, since concrete dust contains silica.
Dig and set the basin
Dig to the depth of the basin, add gravel at the bottom and set the basin level with the floor.
Install pump and piping
Place the pump, connect the check valve and run the discharge pipe through the rim joist or wall.
Patch and test
Pour concrete around the basin, let it cure, then fill the pit with water to confirm the pump cycles.
Need help with a basement pump?
Call dispatch to repair or install a sump pump.
Electrical Safety Comes First
A sump pump runs in a wet place. Use a ground-fault circuit interrupter outlet or breaker, keep the cord away from the pit edge and never use an extension cord. If a dedicated circuit is needed, hire an electrician.
The wet floor around the pit is a shock hazard. Cut power at the panel before reaching for a pump that has stopped working.
Burbank's Recorded Flood Pattern
The Cook County hazard mitigation plan records federal flood disaster declarations that covered Burbank on May 10, 2013 and November 20, 2023, plus Illinois flood declarations in April 2013 and July 2017. It also lists flood-prone locations in Burbank, including the 8600 block of Rutherford Avenue, Narragansett Avenue between 81st and 85th Streets, Parkside Avenue between 78th and 79th Streets and 83rd Street between Narragansett and Melvina.
A new basement pit in those areas should be planned with a backup, since the same storms that fill the pit often interrupt power. The plan counts four repetitive-loss properties in Burbank.
Source: Cook County Multi-Jurisdictional Hazard Mitigation Plan, Village of Burbank annex.
Do It Yourself or Hire a Plumber
The tasks differ in difficulty.
| Task | Homeowner level | Why it matters |
|---|---|---|
| Swap a pump in an existing pit | Reasonable for a handy person | Few parts and no concrete |
| Add a check valve and a union | Reasonable | Simple plumbing |
| Cut the slab and set a new basin | Hard | Dust, heavy work and the risk of cutting drain tile |
| Run discharge through the wall | Moderate | Must seal the opening and slope the pipe |
| New circuit or wiring | Hire an electrician | Water and electricity do not mix |
A plumber can do the whole job or the parts that you choose.
Details That Are Easy to Get Wrong
These are the mistakes behind many repeat calls.
Float placement
If the float touches the pit wall, the pump will not turn on. Check its swing after you set the pump.
Weep hole
A small hole in the discharge pipe below the check valve prevents air lock. Many pumps need one.
Discharge location
The South Stickney Sanitary District states that sump pumps must not be connected to the sanitary sewer. The discharge goes outside, away from the house.
Test the Installation Before You Rely on It
Fill the pit with water from a hose and watch the pump start and stop. Check that the discharge is flowing and that no water leaks at the joints.
Test again after a rainfall, and mark a date on the calendar to test each spring. A pump that sits idle for months can seize.
Materials and Tools Checklist
Gather everything before the slab is opened. A pit left open while you run to the store is a safety and mess problem.
- Pump with a float switch rated for the lift you need
- Basin with a lid, and gravel for the bottom
- Check valve, unions and PVC pipe with primer and cement
- Concrete saw or breaker, and a respirator and eye protection
- Concrete mix to patch around the basin
- A GFCI outlet and a separate circuit if none exists
If any item on this list is unfamiliar, the job is a good candidate for a plumber.
How Long the Pit Takes to Cure
The concrete around the basin needs time to set before you load the pit. Many mixes are firm in a day, but a full cure takes longer. Ask the manufacturer for the schedule of the product you use.
During that period, keep the pump unplugged and keep water out of the pit. Test only after the concrete is firm.
When to Hire Help
If the pit is wet, the floor is finished or the pump has failed during a storm, call for help. Our sump pump service handles installation and repair at any hour.
Homes in Hickory Hills and Stickney are common calls, and the same crews work in Burbank.
Standards Behind the Steps
Pumps are tested to UL 778, and electrical outlets near water should be GFCI protected under the National Electrical Code, NEC.
Burbank requires sump discharge to go outdoors and not into the sanitary sewer.
What to Do Before You Open the Slab
Cutting concrete creates dust and noise. A few precautions reduce the risk.
- Wear a respirator rated for silica dust and eye protection
- Wet the cut to reduce dust
- Check for pipes and wires below the slab before cutting
- Keep the work area clear of other people and pets
- Call a plumber if you hit a pipe or water seeps in
Stop work right away if you find a cable or a gas line.
Installing a Sump Pump: Burbank Questions
Burbank requires a permit for the construction or alteration of plumbing. Ask the Building Department at 708-599-5500, option 2, whether your project needs one.
Outside the house, away from the foundation. It cannot connect to the sanitary sewer.
Deep enough for the pump to cycle with room under the float. Many residential basins run about 18 inches deep or more.
A swap takes an hour or two. A new pit takes a day or more, including curing time for the concrete.
A stuck float, a missing check valve or a high water table are common causes.
Questions about installing a pump? Call dispatch.

